Recent Articles

Road junction

In the field of road transport, a road junction is a place where two or more roads either meet or cross. The main types of road junctions are intersections and interchanges. A road junction may also be called a crossroads. A junction between 3 road segments (arms) is a T junction (two arms form one road) or a Y-junction.

Terminology

Note: The descriptions of road junctions are for countries where vehicles drive on the right side of the road. For countries where driving is on the left, the junctions are the mirror image (the same except that right and left are reversed).

A ramp or slip road is a short section of road which allows vehicles to enter or exit a freeway (motorway).

• A directional ramp always tends toward the desired direction of travel.
• A non-directional ramp goes in a direction opposite to the desired direction of travel. Many loop ramps (as in a cloverleaf) are non-directional.
• A semi-directional ramp exits a road in a direction opposite from the desired direction of travel, but then turns toward the desired direction of travel. Many 'flyover ramps' (as in a stack) are semi-directional.

Weaving is an undesirable situation in which traffic veering right and traffic veering left must cross paths within a limited distance. Weaving creates both safety and capacity problems. Some areas that had such junctions have gone through the expensive process of "unweaving the weave" to improve traffic flow.

Intersections

An intersection is a road junction at which roads meet at grade. Types of intersections include:

• Uncontrolled intersections, without signs or signals (or sometimes with a warning sign). On a 4-way intersection traffic from the right has priority; on a 3-way intersection rules may vary by country: either traffic from the right has priority again, or traffic on the continuing road. For traffic coming from the same or opposite direction, that which goes straight has priority over that which turns off.
• Yield-controlled intersections may or may not have specific "YIELD" signs (known as "GIVE WAY" signs in some countries).
• Stop-controlled intersections have one or more "STOP" signs. Two-way and four-way stops are common.
• Signal-controlled intersections depend on traffic signals, usually electric, which indicate which traffic has the right-of-way at any particular time.
• A traffic circle is a special type of intersection at which traffic streams are directed around a circle. Types of traffic circles include roundabouts, 'mini-roundabouts', 'rotaries', "STOP"-controlled circles, and signal-controlled circles.
• A box junction can be added to an intersection, generally prohibiting entry to the intersection unless the exit is clear.
• While not a specific type of intersection, the US state of Michigan frequently employs a special arrangement for making left turns, known as a Michigan left. These are generally used in conjunction with Signal-controlled intersections, although it can also apply to Stop-controlled intersections.

Interchanges

A highway interchange is a road junction that utilizes grade separation, and one or more ramps, to permit traffic on at least one road to pass through the junction without crossing any other traffic stream. A complete interchange has enough ramps to provide access from any direction of any road in the junction to any direction of any other road in the junction. A complete interchange between two freeways requires eight ramps. A complete interchange between a freeway and another road (not a freeway) requires at least four ramps.

The general rule today is that freeways should have at least one mile between interchanges to prevent excessive weaving between entering and leaving traffic. Unfortunately, most older freeway interchanges do not follow this rule (and are congested as a result).

Types of interchanges between two freeways

• A cloverleaf is a two-level interchange in which left turns are handled by loop ramps. To go left, vehicles first pass either over or under the other road, then bear right onto a one-way ramp that loops 270 degrees to the right and then merges onto the intersecting road. (In countries where cars drive on the left, this would be a right turn.) The major advantage of cloverleafs is that they require only one bridge, which makes such junctions cheap if land is plentiful. A major problem with cloverleafs is weaving (see definition of weaving, above). Cloverleafs also have an enormous land consumption which means that while they are common in the United States and in Germany, only three such junctions are found in the short-of-land United Kingdom, none on the motorway network.
• A stack is an interchange in which left turns are handled by semi-directional flyover ramps. In order to go left, vehicles first turn slightly right (on a 'right-turn' ramp), then go left on a ramp which goes over (or under) both freeways and connects to the 'right-turn' ramp in the opposite quadrant of the interchange. A stack interchange, then, has two pairs of left-turning ramps, which can be "stacked" in various configurations above or below the two through routes. Stacks don't suffer from the problem of weaving associated with cloverleafs, but require massive construction works. A basic stack involves roads on four levels, but in stacks including ramps for direct movement between high occupancy vehicle lanes, even more levels of stack can be needed. This is not only expensive, but also unsightly leading to considerable NIMBY opposition.
• A cloverstack (half cloverleaf, half stack) is an interchange in which left turns are handled by two loop ramps and two semi-directional flyover ramps. A cloverstack avoids the weaving problem associated with cloverleafs, without the expense of a full stack. Cloverleafs are sometimes converted to cloverstacks (by eliminating 2 loop ramps and replacing them with two flyover ramps). Such a conversion improves the capacity and safety of the interchange.
• A stacked roundabout is an interchange where all ramps leading to and from both freeways meet at a roundabout. Such junctions have poor capacity for turning traffic, but are popular in the United Kingdom as they use less land than any other interchange which provides full grade separation for both highways.
• A trumpet is an interchange traditionally used where one freeway terminates at another freeway; it involves at least one loop ramp (for traffic leaving the terminating freeway) whose overpass is shared by traffic connecting to the terminating freeway. These junctions are also useful for toll roads as they concentrate all entering and leaving traffic in a single stretch of road, where toll booths can be installed.
• Hybrids, variations and rare types

Types of interchanges between a freeway and a non-freeway road

• Diamond
• Cloverleaf
• Folded diamond (sometimes called a 4-ramp parclo)
  • a "six ramp parclo" is the same as a folded diamond, except that there are right-turn ramps in what would otherwise be unused quadrants.
• Single Point Urban Interchange (also called "SPUI", "single point diamond", or "X-interchange").
  • SPDI (Single Point Directional Interchange) - identical to a SPUI except that it uses directional ramps.
• Roundabout interchange - this uses a single roundabout which spans the freeway (either above or below the freeway). These are very common in the UK, but almost unknown in the United States.
• Dumbbell interchange - this is similar to a diamond except that it uses roundabouts rather than signals or stop signs where the ramps meet the non-freeway road.