Recent Articles



































Beretta 92F FS



         



The Beretta 92SB-F, Beretta 92FS, Beretta 92G and Beretta 92FS Inox are semi-automatic pistols designed and manufactured by Beretta. The 92FS is given the U.S. Military designation of M9.

[Top]

History

After the interest the Beretta 92SB had created in law enforcement, with sports shooting circles, with the US Armed Forces, Beretta refined the design of the Beretta 92SB into the Beretta 92SB-F and in slightly modified form the Beretta 92G. Beretta did this to participate in military pistol selections in the United States (Beretta 92F) and in France (Beretta 92G).

[Top]

Specifications

Beretta modified the Beretta 92SB slightly, first it redesigned all the parts in such a way that they would be interchangeable between pistols, in order to simplify maintenance for large government organisations. Beretta modified the trigger guard at its front so that one could use finger support for easier aiming. Beretta changed the front angle of the grip to allow for better instinctive aiming. Beretta hard chromed the barrel bore to protect it from corrosion and to reduce wear. Last Beretta applied its new patented surface coating on the frame called Bruniton which provides better corrosion resistance than the blued finish the Beretta 92SB had. On request of the French, for the Beretta 92G it removed the manual safety and modified it into a decocking lever.

[Top]

Intended market

The Beretta 92F was designed for use by major military and law enforcement agencies. During the 1984 M9 pistol trials organized by the US Army, only the Beretta 92SB-F and the Sig P226 qualified, based on its price the Beretta 92SB-F, now renamed Beretta 92F was selected. The excellent GLOCK 17 was not accepted to take part in the trials because of its lack of visible hammer and manual safety. The GLOCK 17s high strategic materials content was also viewed as problematic in times of war. However, the US government demanded a re-test as the US manufacturer Smith & Wesson protested vigorously over the results. The new 1987 M10 trials would confirm the selection of the Beretta 92F. During the pistol trials in France the Beretta 92G also turned out the winner, however the French wanted to manufacture the Beretta 92G under license in France were it would be called the PAMAS-G1. In both cases, initial units would be produced in Italy until US and French based manufacturing would get underway.

[Top]

Design advantages

The Beretta 92F with its slide mounted combined manual safety and decocking lever is very easy to load and unload in a safe fashion. With the safety on, the slide can be manipulated without the risk that touching the trigger would fire the pistol as the safety disconnects the trigger. The improved magazine release button makes the re-loading of the pistol very swift. The safety levers are also placed on both sides of the slide, a feature that enables left handed users to easily use the Beretta 92F. The magazine release button is reversible, another feature that allows left handed users to make the most out of the Beretta 92F. The Beretta 92F retained the reliable function from the Beretta 92SB, properly oiled, cleaned and maintained it would hardly ever fail to function in a moderate climate. The hard chromed barrel bore reduces wear and protects from corrosion. The Beretta 92G which lacks a manual safety, is somewhat less safe to operate, however it is faster into action as no safety needs to be deactivated.

[Top]

Early problems

Beretta now had two major contracts, about 500'000 units for the US Armed forces and around 230'000 units for the French armed forces. This with both clients wanting to receive their pistols as specified in the contracts. In the case of the Beretta 92G, the French would supply the slide steel to Italy, until GIAT would start licensed production. Somehow, at some point in time, Beretta decided to use 5'000 semi finished slides intended for the French to build pistols for the their US customer, this in order to meet deadlines. Not much later after the US Armed forces had accepted these pistols, a few slides of Beretta92Fs and some older Beretta92SBs started to crack and fly off. An investigation would later indentify the lot that had been made with French steel slides as well as US manufactured 9 mm Luger ammunition that was not within specifications. It was also discovered that the locking block required a design change to increase its service life. But until this was resolved, something had to be done to reduce the risk for the user of being struck by the rear half of the slide. The solution was the addition of a slide retention device in form of an enlarged hammer axis pin, the result was the Beretta 92FS. Since then, near all modern Beretta pistols are fitted with such a simple means of user protection. During this time, there were some tests being done with a closed slide, this did however somewhat reduce the reliability of the pistol. Beretta designed a new slide, but this slide would not be disclosed nor enter production as the reason for the slide failures had been discovered, later this slide became known as the Brigadier type slide.

[Top]

Limitations

The Beretta 92FS has the same limitations as the Beretta 92. It is not well suited for use in deserts, jungles and arctic areas. While it will perform quite well in such harsh environments, any negligence in spring maintenance and cleaning will reduce its reliability. The Bruniton finish applied on the Beretta 92F/FS wears away over time which can lead to corrosion and more slide to frame play. The barrel surface, unprotected in the open slide is prone to corrosion.

[Top]

Combat use

During the first Gulf war, the quite new M9s performed very well. However years later, fitted with non factory magazines, badly maintained, the M9s would not perform well in Iraq and Afghanistan.

[Top]

Sports use

Because of the acceptance of the Beretta 92FS by the US Armed Forces, even more civilians have purchased Beretta pistols. As this market turned out to be more demanding concerning durability and corrosion resistance, Beretta made the Beretta 92FS Inox, which has its slide and barrel made out of stainless steel has far less corrosion problems. The Beretta 92 has evolved into high volume shooting sports pistols such as the Beretta 92G Elite II, Beretta 92 Combat, Beretta 92 Stock, Beretta 92FS Brigadier and many other types.

[Top]

Technical data

Type: Beretta 92SB-F/F

Type: Beretta 92FS/FS Inox

Type: Beretta 92G

[Top]

Production

Most models are manufactured by Beretta in Italy or in the USA by Beretta USA. However, the Beretta 92G/96G Elite II and Beretta 92FS/96 Brigadier Inox are only manufactured by Beretta USA, as are the Vertec series. The Beretta 92/96 Combat and 92/96 Stock are only manufactured by Beretta in Italy. Italian made 92s have a nicer surface finish, while US made ones have tighter tolerances. In all other aspects they are equivalent.

[Top]

Note

The SIG P226 was a superior weapon to the Beretta 92F (the original model, entered in the U.S. Army sidearm replacement trials/XM9 Pistol Trials held by the US military in 1984) and current Beretta 92 models, in nearly all respects, except cost. The lower cost of the 92 is the reason why it won the XM9 trials, and many people consider this a big mistake on part of the US Military.

[Top]

See also

[Top]




  View Live Article   This article is from Wikipedia. All text is available under the terms of the GNU Free Documentation License